Floating Shelves – Studio Closet

I built floating shelves in my studio closet in the extra space I created by moving my doorway over 8″.  I almost didn’t bother with moving the doorway because it was extra work and I already have a million other things to do.  I did it though, because it seemed a huge waste NOT to utilize this wall and create ALL THIS NEW STORAGE.  

Door over against the wall = no storage.  Move the door over = storage potential.  Floating shelves spanning this whole wall = tons of new storage!  Shelves are so much more functional than piles of “things” scattered around on the floor, which is what I had going on in here before, so I had to tackle the closet!

This project is sponsored by LIQUID NAILS Fuze*It,  Don’t Just Glue It. Fuze*It

 

Building Floating Shelves

I built three floating shelves along one wall in this closet.  These shelves are 10″ wide by about 9′ long. I used LIQUID NAILS Fuze*It and 3″ long fasteners to build the 2×2 skeleton of my floating shelves and secure it to the walls.  I thought LIQUID NAILS Fuze*It would be helpful on this project because it’s instant grab feature could replace my need for a third (forth and fifth) hand.  

I applied a bead of adhesive onto my 2×2 and pressed it into place and then secured it with 3″ fasteners into the studs.  

I used a laser level to create a level point of reference while securing my 2x2s to the wall.  If you don’t have a laser level,  draw a line on the wall using a long straight edge and level before building your shelves. 

LIQUID NAILS Fuze*It grabs almost instantly while still allowing you to reposition.  It did a fine job acting as my third hand while I got a screws in one end of my 2×2 and then added screws at all the stud locations on the wall.  I secured 2×2 ribs to the three walls that they joined.  I was able to hit two studs in the side wall next to the door.

The opposite side is the slanted ceiling and my shelves aren’t deep enough to hit a second stud (joist) so I’m relying on a screw on one end and adhesive and a few nails on the other end.  LIQUID NAILS Fuze*It bonds almost anything to almost anything else and creates a durable, flexible bond that is twice as strong as fasteners alone.  I’m relying on that strength in this one corner but I added screws through studs everywhere I could.

I ripped short pieces of 2×2 at an angle for this side support.  I had to try a couple times to get it right.  I ended up cutting at 40º, offset about 5/8″ from the bottom of the 2×2.LIQUID NAILS Fuze*It can be applied interior and exterior in hot, cold, wet or dry environments to porous or smooth surfaces.  IF you slightly wet the surface before applying it, it bonds faster!  I wet both the wall and the 2x2s that I applied on this slanted ceiling so the adhesive would bond quickly and I could make sure it stayed in place without being fastened to a second stud. 

I used my nail gun to shoot a few nails into the wall/ceiling and drove a screw into the corner where I could hit a stud.After securing the back and side 2×2 into place, I secured a long 2×2 across the front.  I found it was easier to secure the front 2×2 if I added a brace behind it, against the first side piece.  

I used Fuze*It and screws to secure all the 2×2 pieces to each other. I added all the inside ribs by glueing up both ends, pulling the front 2×2 forward and sliding the ribs in place.  After inserting each rib, I secured it to the front 2×2 with one 3″ screw.   I used a clamp to keep both pieces flush with each other while driving the screw.

After all the inside ribs were in place, I secured them all to the back 2×2 by driving screws in at an angle from one side.  Again, I used a clamp to keep the surfaces flush with each other while securing.  
Once my 2×2 skeletons were built, I added plywood.  I ran a bead along the sides of my plywood as well as on the ribs 

The LIQUID NAILS Fuze*It really held this light 1/4″ plywood in place once I pressed the two surfaces together.  So, I felt confident using 23 ga nails to hold it in place while the adhesive set up.

I used 1/2″ plywood on the tops and secured that with adhesive and nails as well.  

I used 1×3 primed pine for the front of my floating shelves.  I applied LIQUID NAILS Fuze*It to the front of the 2×2 and as much plywood as I could because I wanted the front to bond to the whole “wood sandwich”.  

I used 16 ga nails to secure the face to the shelves.

In addition to the three shelves on the side wall, I put a 22″ wide by 8′ long shelf along the back wall.  

At that width and depth, the 2×2 ribs are not going to be enough to fully support it.  I used 1/2″ plywood on the top and bottom to give it additional strength and I’ll be adding a little support after I get the flooring installed.  I went ahead and built the shelf now though, so I could get it sanded, caulked and painted with the other shelves before the flooring goes in.

It was not an easy task because the half sheet of 1/2″ plywood was to heavy for the LIQUID NAILS Fuze*It to hold it in place and I hadn’t planned ahead and brought up more than the single clamp I’ve been  using.  I had to be flexible while I got some nails in there.

After building all my floating shelves I just had to fill the nail holes, sand, prime and paint.

Before I installed my floating shelves, I installed beadboard on the ceiling and walls. It is 100 times more work to install beadboard in between your floating shelves than before you put them up.  I learned that the hard way in my hall closet with floating shelves.  I wanted to use up a bunch of beadboard scraps so I may have done it that way regardless of the extra work.  I didn’t have that problem this time around so I installed full sheets of beadboard in this room and got it done beforehand.

Now I just have to install my flooring and this closet will be done!

I’ll be so glad to have a space to put my tools away in an organized fashion while I continue building the rest of my studio!  Then, once the building is complete I’ll have plenty of shelving for my crafting supplies. Can’t wait!

This post is sponsored by LIQUID NAILS Fuze*It, available exclusively at The Home Depot.  I was compensated for my time and effort in creating this project to share with you.

The post Floating Shelves – Studio Closet appeared first on Sawdust Girl®.

from http://bit.ly/1TbPnTO

DIY_Express